1
Advertising
Liftmaster 829LM Garage Door Monitor Instructions. Learn how to program to your Liftmaster or Raynor opener by using the 829LM installation manual. Use the 829LM monitor to know when your garage doors are open with visual and audible alerts. LiftMaster LJ8900W Light-Duty Commercial Jackshaft Operator w/Built-In Wi-Fi for Sectional Doors Manual 3; LiftMaster Elite Series 8500W Wall-Mount Garage Door Opener w/Built-In Wi-Fi and Battery Backup; LiftMaster Elite Series 8500W Wall-Mount Garage Door Opener w/Built-In Wi-Fi and Battery Backup Manual 2; Liftmaster 8500 Wall Mount Garage.
For use with Security✚ 2.0
TM
Garage Door Openers. All Security✚ 2.0
TM
Garage Door Openers have a
yellow Learn button and two yellow antennas. The features are adjustable and may be turned off or on
as desired. Refer to the Feature Settings section.
Smart Control
Panel
®
Safety
Reversing Sensors
Yellow
LEARN Button
SMART CONTROL PANEL
®
MODEL 880LM
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
• Install door control within sight of garage door, out of reach of children at a minimum height of
5 feet (1.5 m), and away from ALL moving parts of door.
• NEVER permit children to operate or play with door control push buttons or remote control
transmitters.
• Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path
of closing garage door.
Feature Overview
MAINTENANCE ALERT SYSTEM (MAS)
This feature assists the homeowner in ensuring the garage door opener system stays in good working
condition. A maintenance alert message will display on the screen indicating the garage door opener may be in need of maintenance.
The MAS feature MUST be activated at time of installation. The factory setting is off.
LOCK
The LOCK feature is designed to prevent activation of the garage door opener from remote controls
while still allowing activation from the door control and keyless entry. This feature is useful for added peace of mind when the home is empty (i.e. vacation).
LIGHT BUTTON
Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned on
they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after the specified period of time (the factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in motion. The duration of the light timing can be adjusted by accessing the menu using the navigation buttons.
SCREEN
The screen will display the time and temperature until the menu button is pressed, and then it will
display the menu options. If there is a problem with the garage door opener the screen will display the Diagnostic Code.
MOTION SENSOR
The motion sensor will automatically turn on the garage door opener lights when motion is detected.
The lights will come on for the set period of time, then shut off. The factory setting is on and set at 4-1/2 minutes.
TIMER-TO-CLOSE (TTC)
DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors.
Factory default is set to off. TTC can be set to automatically close your garage door from the fully open position after a specified period of time (1, 5, 10 minute intervals or a custom setting up to 99 minutes). The garage door opener will beep and the lights will flash before closing the door. The screen on the door control can display the status of the TTC. TTC WILL NOT work if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned. This feature is NOT intended to be the primary method of closing the door. A keyless entry should be installed in the event of an accidental lock out when using this feature.
Advertising
Table of contents
Popular Brands
Popular manuals
Page 3: Garage door opener lights, Motion sensor, Light feature, Timer-to-close (ttc), Lock, Battery backup only, Maintenance alert (mas)
Advertising
3
Operation
PUSH BAR
Press the push bar to open or close the door.
NAVIGATION BUTTONS
Use the navigation buttons to make selections
and program features.
GARAGE DOOR OPENER LIGHTS
Press the LIGHT button to turn the garage door
opener lights on or off. When the lights are turned on they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after the specified period of time (the factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in motion.
Push Bar
LIGHT
Button
Screen
Motion
Sensor
Navigation
Buttons
The TTC feature will deactivate if the garage door
encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door will close when the garage door opener is activated.
To temporarily suspend the TTC feature press
and release the HOLD button. Press REL button to resume normal TTC operation.
TIMER-TO-CLOSE (TTC)
DO NOT enable TTC if operating a one-piece
door. TTC is to be used ONLY with sectional doors. Once the TTC has been set and the door is open, the selected close interval will be displayed on the screen and toggle between the time and TTC message. The garage door opener will beep and the lights will flash before closing the door. When the TTC is on the following message will display on the door control:
TO REMOTE
BATTERY BACKUP ONLY
If your garage door opener has a battery backup
one of the following messages will display on the door control if there is a problem with the battery:
MAINTENANCE ALERT (MAS)
When the maintenance alert is on and the garage
door opener needs maintenance the following message will display on the screen:
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
Program
Press the button on the remote
control that you wish to operate your garage door.
Enter a 4-digit personal identification
number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button.
PIN
?
?
?
?
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PRS
8
TUV
9
WXY
0
QZ
*
#
ENTER
0 QZ
*
#
ENTER
OR
4a
4b
Press the navigation
button below 'MENU' to view the Features menu.
Select 'REMOTE' or 'KEYPAD'
to program from the program menu. Press
to continue.
1
3
2
Liftmaster Manual Pdf
The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.
Repeat the steps above for programming additional remote controls or keyless entry devices. If programming is unsuccessful, refer to the remote control instructions.
MOTION SENSOR
This feature will automatically turn on the garage door opener lights when motion is sensed. The lights will come on for the set period of time, Canon microfilm scanner 800 user manual. then shut off.
LIGHT FEATURE
The lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken. If using the garage door opener light as a work light, turn the light on using the light button on the wall control or the light will turn off if you are beyond the range of the sensor.
LOCK
When the Lock feature is on, your remote
controls have been disabled and the following message will display on the door control: Liftmaster Wall Remote User Manual 3220 Driver
Use the navigation buttons to
scroll to 'PROGRAM' and press the navigation button under
to continue.
Advertising
Popular Brands
Liftmaster Remote Control Manual
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |